Looking for:
Mitsubishi outlander service manual download |
MITSUBISHI OUTLANDER SERVICE MANUAL (Volume 1, 2, 3) – PDF Download - Mitsubishi Outlander Workshop Manual
MITSUBISHI OUTLANDER SERVICE MANUAL Pdf Download | ManualsLib.Mitsubishi Outlander Repair & Service manuals - Free Download PDF
Quick Links. See also: Owner's Manual , Manual. Previous Page. Next Page. Automobile Mitsubishi Outlander Service Manual pages. Do not pour oil or water on applied locations or do not start the engine until sufficient time approxi- mately one hour passes. The application procedure of FIPG may differ depending on areas.
Follow the procedure in the body of the manual to apply FIPG. Use special tool Flywheel stopper MB to secure the drive plate. Apply an appropriate and minimum amount of engine oil to the threaded portion of the crankshaft and lower part of the flange. With the chamfered side on the inside of the washer facing the bolt top, install the crankshaft pulley washer to the crankshaft pulley centre bolt.
Check that the injector rotates smoothly. If it does 5. Securely assemble the injector to the injector not rotate smoothly, the O-ring may be caught. Remove the injector and check the O-ring for damage. The strong press fit can possibly cause the oil leakage, damaging the front oil seal.
Use special tool Bush remover and installer base MB in order to press-fit the front oil seal into the timing chain case as shown in the illustration. Tighten the cylinder head cover to the tightening torque of 3.
Then, tighten it to the specified torque of 5. Align the timing mark of the inlet V. Retard Tape port Advance port Inlet V. Exhaust sprocket camshaft timing mark sprocket timing mark Make a hole Retard Advance Turn the inlet V.
Check it smoothly moves in the range of A approximately Select a valve tappet in the following procedure. Set the dowel pins of the camshaft at the 7. When the measured value Measure camshaft height camshaft major axis. If deviates from the standard one, replace the the height exceeds the limit, replace the camshaft. Completely remove oil, scale, sealant, carbon, bolts on the timing chain side.
After cleaning oil passages, blow air to make sure that they are not clogged. Timing chain side AK AK Measure overall length of the valve. Measure clearance between the valve guide and If the limit is exceeded, replace the valve. Press fit the valve seat, taking care not to score the cylinder head bore at room temperature.
Pry the illustrated position with a screwdriver or tap the boss with a hammer. If the ladder frame does not come off, insert a 1. Wipe off the dirt on the crankshaft sprocket and the crankshaft using a rag, and then remove the 1. CAUTION Do not apply oil to the circumference of the oil seal and oil seal pressing hole on the cylinder block side to prevent teeth from pulling out.
Use special tool Flywheel stopper MB to 3. Completely remove liquid gasket adhering to the cylinder block and ladder frame. Wipe the dirt on the crankshaft sprocket and the 6. While slanting the balancer shaft module, align crankshaft using a rag, and then remove the the link plate blue of another balancer chain with grease from the portion shown in the illustration. Pull out the hexagonal bar wrench from the prevent the plunger of the chain tensioner from balancer module sprocket.
Apply engine oil to thread of crankshaft and bolt 5. Tighten drive plate bolts to temporary torque of 40 seat area of drive plate. Insert the push rod into the piston pin from the connecting rod big end. Piston Driving it in hard causes breakage of piston rings rings can be assembled by hand without using the and damage to the crank pin.
Make sure that clearance of the thrust of the 3. A connecting rod bearing has an identification connecting rod big end is appropriate. Standard value: 0. Put a paint mark on the bolt head as illustrated.
Put piston rings into the cylinder bore, press them 7. Measure the crushed Plastigage width area most widely crushed using a scale printed on the Plastigage bag.
Install the selected crankshaft bearing lower. Install the crankshaft bearing cap with reference No. Measure the bore and cylindricity of the cylinder using a cylinder gauge. Print page 1 Print document 63 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk.
Upload from URL.
No comments:
Post a Comment